最終更新日: 2026-11-16 5 分で読めます

Laser Tube Cutting Machine Guide: Round & Square Tube

A laser tube cutting machine rotates round, square, rectangular, and oval tube in motorized chucks while a fiber laser cuts lengths, holes, notches, copes, and slots in 一つ program. Typical machines handle diameters from about 20 to 220 mm and wall thickness up to roughly 8 mm, with larger models beyond that. 一つ machine replaces the saw, drill, and milling steps of traditional tube fabrication, and joinery features like tabs and slots make frames self-locating for welding.

Sheet lasers get the attention, but tube is where fabrication labor hides. A frame that needs forty tubes traditionally needs forty saw cuts, a marking-out session, dozens of drilled holes, milled notches, and a fitter persuading it all square before welding. A tube laser collapses that chain into programs and chucks. This guide explains how the machines work, which chuck configuration and capacity to buy, the joinery features that justify the investment, and the labor arithmetic behind the category's growth.

Laser Tube Cutting Machine Guide: Round & Square Tube

Why Tube Cutting Is Its Own Machine

A tube laser is not a sheet machine with a rotary bolted on. The material is a long, heavy bar that must rotate precisely while being fed axially, so the architecture is built around chucks: motorized jaws that grip, spin, and advance the stock through a fixed cutting zone. The controller synchronizes rotation, feed, and the cutting head so a contour can wrap around a corner of square tube or spiral along a round one.

Support is the quiet engineering problem. A 6-meter bar whips and sags if gripped only at its ends, and wall thickness as light as fencing tube dents under careless clamping, which is why chuck count and support design separate the machine classes:

 追加されるもの以下のためにベストサイズ測定
2チャックThe baseline: front chuck feeds and rotates, rear chuck grips the stockGeneral fabrication on common tube sizes and lengthsShortest remnant the machine leaves per bar
3チャックA middle chuck supports the tube through the cutting zoneLonger parts, thin walls, and tighter remnant controlVibration and cut quality near bar ends
4チャックFull support along the bar with near-zero remnant designsProduction shops where material yield is moneyUsable length cut from each purchased bar
Auto loading bundleA rack feeds bars in and parts drop out without an operator at the chuckLights-out and high-volume productionParts per shift per operator

Remnant length deserves the attention the table gives it. Every bar ends with a stub the chucks cannot feed past, and across thousands of bars that stub is purchased steel in the scrap bin. Designs that cut the remnant to a few centimeters, or near zero on 4-chuck machines, quietly repay their premium in material yield.

Capacity: Diameter, Wall, and Length

⦿ Diameter range: mainstream machines cover roughly 20 to 220 mm across round, square, rectangular, and oval sections; heavy models extend well beyond for structural work.

⦿ Wall thickness: up to about 8 mm on typical configurations, set by laser power; thicker walls call for higher wattage.

⦿ Stock length: standard machines load 6 m bars, with longer-bed options; part length is limited by the machine's unload side.

⦿ Profiles beyond tube: many machines also cut angle, channel, and flat bar, which widens the work a single machine can quote.

Match capacity to the catalog, not the brochure: the machine must swallow your largest regular section with clamping room to spare, and laser power must carry your thickest wall at production speed. The wattage-to-thickness relationship is the same 一つ documented in the fiber laser cutting thickness, speed, and power guide, applied to wall thickness instead of plate.

Thin walls and cosmetic sections

2 capacity details separate adequate machines from frustrating ones. Thin-wall tube, common in furniture and display work, dents under aggressive jaws and burns through under careless parameters, so clamping pressure control and tested thin-wall settings matter more than headline capacity. Cosmetic sections, polished stainless and pre-finished tube, need jaw covers and supports that do not scratch; ask to see a polished part come off the machine, not just mild steel.

Joinery Features: The Real Selling Point

Cut-to-length is the least of what the machine does. The features that change a fabrication business are the ones cut into the tube:

⦿ Tabs and slots: mating features that locate parts against each other, so a frame self-assembles square and the fitter's marking-out disappears.

⦿ Copes and saddles: fish-mouth profiles where 一つ tube meets another, cut to fit instead of ground to fit.

⦿ Holes and arrays: bolt patterns and hardware holes placed by program, replacing the drill press and its layout errors.

⦿ Notches and miters: corner joints cut at angle with the weld gap designed in.

Shops describe the downstream effect the same way: welding time drops because fit-up time drops, and quality rises because the parts can only go together 一つ way. For joints that need full weld preparation on the tube ends, the step up is the 3D チューブレーザーベベル切断機, which adds angled bevel cutting to the same rotating workflow.

Weld-ready edges and what comes after the cut

Tube parts usually head straight to welding, and the laser's narrow kerf leaves edges that weld without grinding on common wall thicknesses. Pierce points and dross behave as they do on sheet: tuned parameters keep the inside of the tube clean, which matters on sections that carry fluid or stay visible. For production that cannot tolerate any inside dross, discuss the nozzle and gas setup for your wall thickness during the demonstration rather than after delivery.

Automation: When the Bundle Loader Pays

A manual-load machine keeps an operator at the chuck end: load a bar, run the program, catch the parts, repeat. An automatic bundle loader stacks that work: a rack of bars feeds in 一つ after another, parts drop to a conveyor or bin, and the operator becomes a supervisor of several machines or a welder between loads.

The decision is a volume threshold. A shop cutting a few bars a day gains little; a shop running hundreds of repeat parts gains a shift's labor and the lights-out hours after it. Price the loader against the loaded labor cost it replaces, and note that it also steadies quality, because bars feed with the same orientation and pace every time.

Who Buys Tube Lasers, and Which Configuration

⦿ Furniture and display frames: light sections, high part counts, tabs and slots everywhere; a 2 or 3 chuck machine with a loader earns fast.

⦿ Fitness equipment and seating: curved and oval sections with cosmetic surfaces; support quality and scratch-free clamping matter.

⦿ Railings, gates, and fencing: mixed profiles and miters; a flexible manual-load machine covers the variety.

⦿ Machine frames and skids: heavier square sections and bolt arrays; capacity and wall thickness set the spec.

⦿ Contract tube cutting: the service business case, where a loader and near-zero remnant design are the margin.

Finished examples across these industries are collected in the laser cutting machine project gallery, and they are a faster education in what tabs, copes, and arrays look like on real parts than any specification page.

Software carries half the value

The joinery library lives in software, so evaluate it as seriously as the hardware. Good tube software imports 3D assemblies and unwraps each tube's features automatically, places tabs and copes from a menu, and nests parts along bars to squeeze the remnant. Weak software leaves the programmer drawing every notch by hand, which quietly gives back the labor the machine saved. Ask the demonstration to start from your own frame model, not the supplier's sample file.

The Labor Math of Replacing 3 Stations

Take an illustrative frame of forty tubes. Traditionally: forty saw cuts with handling between them, marking out, sixty drilled holes, a dozen milled notches, and fit-up persuasion at the welding table, call it a long day across 3 machines and 2 people. On a tube laser, the same forty parts run from 3 bars in under an hour, arrive deburred of layout error by definition, and lock together for welding.

The saved hours are only half the account. The saw, drill, and mill stations shrink to backup roles, their floor space returns, and the schedule risk of 3 queues becomes 一つ queue. Shops that quote frames weekly find the machine's payback resembles the sheet laser's a decade ago: the 1st mover in a region wins work on lead time until the neighbors catch up. Configurations across capacities and chuck counts are compared on the ファイバーレーザーチューブカッター page, alongside the wider fiber laser cutting machine range.

Laser Tube Cutting Machine Guide: Round, Square and Profile Cutting ExplainedSEO Assets

購入者チェックリスト

✔ List your sections: largest and smallest diameter, heaviest wall, and longest part, with clamping headroom.

✔ Choose chuck count by part length, wall delicacy, and how much remnant yield is worth to you.

✔ Confirm the joinery library: tabs, slots, copes, and miters programmed in the software, not promised in the brochure.

✔ Decide the loader by daily bar count, and leave space for it even if it comes later.

✔ Cut your own frame kit at demonstration, and weld it; the fit-up tells the truth.

Replace the Saw, Drill and Mill with 一つ Program

Compare chuck configurations, capacities, and bundle loaders on the ファイバーレーザーチューブ切断機, and get a free quote matched to your sections, wall thicknesses, and part volumes.

参考文献

CNC木工旋盤の価格:シングル、ダブル、四軸

2026-10-10前へ

次の投稿はありません

関連ソリューション

ファイバーレーザーカッターマシンのパフォーマンスに影響を与えるものは何ですか?
2021-08-312-Minute Read

ファイバーレーザーカッターマシンのパフォーマンスに影響を与えるものは何ですか?

ファイバーレーザー切断機の性能に影響を与える要因には、レーザー発生器、光路、エアコック、補助ガス、切断パラメータ、材料などがあります。

ファイバーレーザー切断の1時間あたりのコスト:実際の運用コスト
2026-10-296-Minute Read

ファイバーレーザー切断の1時間あたりのコスト:実際の運用コスト

ファイバーレーザー切断機の稼働コストは、オペレーターの人件費を含めて、通常1時間あたり30ドルから65ドル程度です。人件費を除くと、電気代、アシストガス代、消耗品代、メンテナンス費用は、レーザー出力とガスの種類によって異なりますが、1時間あたり約6ドルから40ドル程度になります。電気代が最も安く、1時間あたり2ドルから7ドル程度です。窒素ガス代と人件費が最も高額です。

金属用ファイバーレーザーカッターベスト10
2026-04-179-Minute Read

金属用ファイバーレーザーカッターベスト10

家庭用から商業用、趣味用から工業用、エントリーレベルからプロモデルまで、2026 年のあらゆるニーズに最適な金属レーザーカッターを探ります。

アルミニウムのレーザー切断:問題点、解決策、および厚さの制限
2026-08-087-Minute Read

アルミニウムのレーザー切断:問題点、解決策、および厚さの制限

アルミニウムは、業界で最もレーザー切断される金属の一つであると同時に、最も多くのトラブルシューティングのスレッドを生み出す金属でもあります。アルミニウムは、溶融させるはずのレーザー光を反射し、他のほとんどのエンジニアリング金属よりも速く切断箇所から熱を奪い、鋼材切断業者が気にする必要のない、しつこい底部のドロスを生成します。このガイドでは、アルミニウムがレーザーと相性が悪い理由を説明し、アルミニウム切断不良のほぼすべての原因となる4つの問題点を解説し、マーケティング上の主張と実際の機械による切断結果を区別する、厚さとワット数の関係を示します。

インサイズとミツトヨのノギス:どちらが価格に見合う価値があるのか​​?
2026-07-287-Minute Read

インサイズとミツトヨのノギス:どちらが価格に見合う価値があるのか​​?

インサイズとミツトヨのノギスを比較:実際の価格、精度仕様、フォーラムの評価、そして偽物のミツトヨを見分ける方法。あなたの作業場と予算に合ったノギスはどちらでしょうか。

初心者向けのレーザーカッターの使い方
2023-09-263-Minute Read

初心者向けのレーザーカッターの使い方

初心者またはオペレーターは、レーザー切断システムを開始する前に知っておくべき 3 つのヒント、レーザー カッターの使用方法を学ぶための 12 の手順、レーザー マシンに関する 12 の注意事項を学ぶ必要があります。

レビューを投稿する

1つ星から5つ星の評価

自分の考えや気持ちを他の人と共有する

クリックしてキャプチャを変更